37M PUMPCRETE 5 RZ BOOMS
Quotation List
H.S. CODE: 8479.1090
Marks
No.
Description of Goods
Qty.
Unit Price
Total Price
N/M
1
37M PUMPCRETE
KNL5231THB 37-5RZ
1 UNIT
USD
USD
EXW
Notes:
1. Payment terms: 30% T/T in advance, 70% TT should be paid before shipment.
2. Delivery time: 25~45 working days.
3. Warranty period: 12 months after installation. (Refer attached “Annex of WARRANTY”)
4. No. of container required: 1*40FR.
5. Trade terms: EXW, FOB, C&F, CIF.
主要参数 Main Specification:
型号 Model
KNL5231THB 37-5RZ
项目 Item
单位 Unit
值 Parameter
泵送系统
Pumping System
最大理论输送量 (高压/低压)
Max. Theoretical Concrete Output (H/L Pressure)
m3/h
66/111
混凝土最大出口压力 (高压/低压)
Max. Theoretical Output Pressure (H/L Pressure)
MPa
10/6
额定工作压力
Rated Working Pressure
MPa
32
泵送频率 (高压/低压)
Pumping Frequency (H/L Pressure)
min-1
19/32
料斗容积
Hopper Capacity
L
600
上料高度
Feeding Height
mm
1200
液压系统型式
Hydraulic System Mode
开式
Open Loop
分配阀形式
Distribution Valve Mode
S管阀
S Valve
油缸缸径×行程
Oil Cylinder Diameter × Stroke
mm
Φ125×1400
混凝土缸径×行程
Concrete Cylinder Diameter × Stroke
mm
φ230×1400
液压油冷却
Hydraulic Oil Cooling
风冷
Air Cooling
推荐塌落度
Recommended Concrete Slump
cm
12~23
最大骨料尺寸
Max. Aggregate Dimension
mm
40
臂架
Placing Boom
结构形式
Structure Type
37-5RZ
最大布料高度
Max. Placing Height
m
36.1
最大布料半径
Max. Placing Radius
m
32.6
最大布料深度
Max. Placing Depth
m
25.5
回转角度
Slewing Angle
±270° (540°)
输送管直径
Delivery Pipe Diameter
mm
125
末端软管长度
End Hose Length
mm
3000
臂架最小打开高度
Min. Height Of Opening Placing Boom
mm
9000
支腿跨距(前×后×纵向)
Outriggers Span (Front × Rear × Side)
mm
6140×7606×8446
底盘及整车Chassis & The Whole Machine
底盘型号
Chassis Model
ZZ5231N521GE1
轴距
Wheelbase
mm
5200
发动机型号
Engine Model
MC07.31-50
发动机额定功率
Engine Power
KW
228KW
燃油箱容积
Fuel Tank Volume
L
400
尾气排放标准
Tail Gas Exhaust Standard
国V
EURO V
整车外形尺寸 (长×宽×高)
Overall Dimension (L x W x H)
mm
9840x2496x3870
其它Others
润滑方式
Lubrication Mode
手动液压两用同步润滑泵
Manual Hydraulic Dual Purpose Synchronous Lubricating Pump
液压油箱容积
Hydraulic Oil Tank Volume
L
500
控制方式
Control Mode
手动+遥控
Manual+Remote Control
压力水箱最大压力
Max. Water Tank Pressure
MPa
0.8
水箱容量
Water Tank Volume
L
400
混凝土管清洗方式
Concrete Pipeline Cleaning Mode
水洗/干洗
Water/Dry Cleaning
主要部件信息 Main Components Configuration:
臂架控制模式
Boom Control Mode
手动、无线遥控系统
Manual & Wireless Control System
支腿打开方式
Legs Open Type
前X型伸缩支腿,后摆腿
Front:X Type Retractable Leg, Back:Swing Leg
臂架钢材
Boom Steel
1000MPa高强钢板
1000MPa High Stress Steel Plate
控制电源
Control Power Supply
底盘自带电源
Chassis With Power Supply
工作电压
Working Voltage
DC24V
继电器品牌
Relay Brand
欧姆龙
OMRON
接近开关品牌
Proximity Switch Brand
图尔克
TURCK
无线遥控器品牌
Wireless Remote Controller Brand
国产比例遥控器
Domestic Proportion Remote Controller
液压系统类型
Hydraulic System Type
开式
Open Loop
主液压油泵品牌
Main Hydraulic Pump Brand
普什/力士乐
PUSH/REXROTH
主油泵排量
Main Hydraulic Pump Displacement
190ml/r
主电液换向阀品牌
Main Electro-Hydraulic Valve Brand
美国伊顿
American EATON
高压过滤器品牌
High Pressure Oil Suction & Return Filter Brand
德国贺德克
Germany HYDAC
臂架多路阀品牌
Boom Multi-Way Valve Brand
意大利沃尔夫
Italy Walvoil
齿轮泵
Gear Pump
意大利凯斯帕
CASAPPA
臂架油泵品牌
Boom Oil Pump Brand
力源/力士乐/普什
LIYUAN/REXROTH/PUSH
支腿多路阀品牌
Leg Multi-Way Valve Brand
台湾油力/博尔法
TAIWAN YOULI/BOLEV
油缸液压密封件品牌
Oil Cylinder Hydraulic Seals Brand
美国派克
American Parker
液压胶管品牌
Hydraulic Hose Brand
美国盖茨
American Gates
液压油冷却方式
Hydraulic Oil Cooling
风冷
Air Cooling
高低压切换方式
High And Low Pressure Exchange
电控自动
Electric Automatic Control
分动箱品牌
PTO Box Brand
株齿/斯宝
ZHUCHI/STIEBEL
回转减速机品牌
Turret Reducer Brand
宁波中意
Ningbo ziHYD
技术优势 Technical Advantage:
1、Φ230输送缸配Φ125油缸,对混凝土要求低,既能满足低压大排量泵送需要,也能实现高压小排量替代车载泵需求。
1.Φ230 delivery cylinder and Φ125 oil cylinder, low requirement for concrete. Both to meet the needs of low pressure large displacement pump, but also to achieve high pressure small displacement car replacement’s needs.
2、通过有限元分析,动力学分析计算和实验,以精确的数据支持为基础,材料采用高强度低合金钢板,所有的材料与焊缝均通过100%无损探伤,确保X型支腿和臂架结构的合理性和可靠性。
2.According to finite element analysis, dynamic analysis calculating and testing, based on the accurate data support, materials using high strength low alloy steel plate. All the materials and welds are through 100% NDT, to ensure that the X type leg and arm frame structure is reasonable and reliable.
3、发动机转速自动控制,臂架动作时转速1100-1200rpm,泵送时转速随排量在1200-1600rpm之间变化,排量低转速低,排量高转速高,此转速区间为发动机扭矩最大部分,燃油经济高效。
3.The engine speed automatic control, speed change with the displacement in the 1200-1600, low displacement with low speed, large displacement with high speed, this speed range is the largest part of the engine torque, fuel economy and efficiency.
4、主阀组采用双泵双回路电控高低压切换阀块,高低压切换一键完成,不需停泵,且油路简单,故障率低,维修方便。主油缸由主油泵供油,摆缸由齿轮泵带蓄能器供油,泵送排量最小时可在每小时5方以内,最大时可达到100方以上。个别厂家由主油泵同时为主油缸及摆缸供油,无法实现小排量泵送:主泵排量极低时,S管摆动也相应变慢,无法泵送。
4.The main valve group adopts double pump double loop control of high and low pressure switch valve block, high and low voltage switch a key to complete, do not need to stop the pump, and the circuit is simple, low failure rate, easy maintenance. The main oil cylinder is supplied by the main oil pump, and the tilt cylinder is supplied by the gear pump with accumulator. The pump displacement can be less than 5 per hour, the maximum can reach more than 100 cu meters. Individual manufacturers by the main oil pump at the same time as the main oil cylinder and the cylinder oil supply, can not achieve a small displacement pump: the main pump displacement is very low, s tube swing also correspondingly slow, can not pump.
5、两用同步润滑系统,工作时由摆阀控制油驱动,不工作时可推动手动摇杆进行润滑。循环口可为料斗内大小轴承座润滑,同步口可为泵送活塞润滑,可将活塞寿命提高至3万方以上。
5.Dual synchronous lubricating system. when working, the swing valve control oil drive, when not working, can push the rocker manual lubrication. Circulation port can be a bearing size hopper seat lubrication, synchronization can be sent to the piston pump, the piston’s life increased to above 30 thousand cu meters.
6、臂架采用负载敏感比例多路阀,动作速度无级调节,快慢自如,操作性能极佳;不但可以实现遥控控制,还可以实现紧急情况下的应急手动操作;搅拌与支腿由齿轮泵供油,带有压力继电器可实现搅拌自动反转,防止较大石子卡住叶片。
6.The arm frame adopts the load sensing proportional multi way valve, the movement speed is stepless regulation, the speed is easy, the operation performance is excellent. Not only can realize the remote control, but also can realize the emergency manual operation. Mixing and supporting legs by the gear pump oil, with the pressure relay can achieve automatic mixing and reverse, to prevent large stones stuck blade.
保修条款补充解释 Annex of WARRANTY
第一条 Article 1
质量要求、技术标准:出卖人提供符合国家标准的合格产品,以产品使用说明书中的主要参数为准。
Quality requirements, technical standards: The seller provides qualified products that meet the national standards, which are subject to the main parameters in the product manual.
第二条 Article 2
出卖人对产品质量负责的条件及期限自买方收到产品第二日起,产品质量保修期12个月(易损件、电器件除外);在保修期内出现质量问题由出卖人负责修复。因买受人原因造成的事故修理所产生的费用由买受人承担,出卖人对产品实行终身服务(并合理收费)。
The conditions and time limit for the seller to be responsible for the quality of the product shall be 12 months from the date of receipt of the product by the buyer (except for consumable parts and electrical components); the seller should be responsible for the quality problems arise during the warranty period. The expenses incurred by the accident repair caused by the buyer are undertook by the buyer, and the seller provides lifelong service (and reasonable charges) for the product.
第三条 Article 3
其它约定事项:(保修期及保修期后如需工程师到场服务,需要支付工程师每天的费用为200美金,由客户提供签证,食宿和往返费用;费用根据天数计算,由买方支付)。
Other agreed matters: (During and after warranty time if customer needs our engineer come to the jobsite for service, customer should pay the engineer's daily fee is USD200, the customer provides the visa, accommodation and round-trip costs; the customer pays according to the number of days.